HP Laserjet Pro MFP M28W, HP LaserJet Pro M28-M31w Printers - Blinking Lights

HP Laserjet Pro MFP M28W, HP LaserJet Pro M28-M31w Printers - Blinking Lights

This document is for the HP LaserJet Pro MFP M28w, M29w, M30w, and M31w wireless printers.
The following sections describe the most common error conditions with combinations of blinking (flashing) lights displayed on the printer control panel, followed by solutions for each combination. Find the blinking light pattern that displays on the control panel, and then follow the steps to resolve the issue.
  1. Control panel LED display
  2. Copy Setup button
  3. Start Copy button
  4. Cancel button
  5. Supplies light
  6. Power button/light
  7. Attention light
  8. Wireless button/light
  9. ID Copy button
  10. Down arrow button
  11. Up arrow button

The Wireless light blinks

The Wireless light  blinks when a connection is configuring or when the printer cannot find a wireless signal or cannot connect to the network.

Step 1: Wait for the printer to establish a connection

The Wireless light blinks when the printer is attempting to connect to the wireless router or access point. Wait a few minutes, and then check the light again.
  • If the Wireless light is on and steady, the printer is connected and you can stop troubleshooting.
  • If the Wireless light is still blinking, continue to the next step.

Step 2: Check for issues with the wireless network

The following factors can cause the printer to lose the wireless connection:
  • The network connection is no longer active, or has low signal strength.
  • The printer goes into sleep mode or standby mode.
  • The printer is either too far away from the wireless router, or too close to it. The recommended distance between the printer and the router is 1.0 meter to 1.5 meters (3 ft to 5 ft).
  • A firewall prevents the printer from accessing the computer and wireless network.
  • A nearby device that emits radio signals (such as a microwave or cordless telephone) might interfere with the wireless connection.
  • A virtual private network (VPN) prevents the printer from accessing the computer and wireless network.
Check the Wireless light after correcting any items on the list.
  • If the Wireless light is on and steady, the printer is connected and you can stop troubleshooting.
  • If the Wireless light is still blinking, continue to the next step.

Step 3: Connect the printer to your network

For more information about connecting the printer to the wireless network by installing the printer software, see Wireless Printer Setup (Windows) or Wireless Printer Setup (Mac), depending on your operating system.

Attention and Ready lights blink

This condition occurs when the printer is too hot to continue printing. To resume printing, wait for the printer to cool down.

Er/01 displays and the Attention light blinks

An Er/01 error message occurs when the input tray is empty. To resolve the error, load paper into the input tray. For more information about loading paper, go to Loading Paper, Envelopes.

Er/02 displays, the Attention light blinks, and the Ready light is on

An Er/02 error message indicates the toner cartridge access door is not closed completely.
Close the toner cartridge access door completely.

Er/04, Er/05, or Er/06 displays, the Attention light blinks, and the Ready light is on

An Er/04, Er/05, or Er/06 error message indicates a paper jam.
Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper. For detailed troubleshooting, go to Paper Jam Error.

Er/07 displays, the Attention and Supply lights blink, and the Ready light is on

An Er/07 error message indicates the toner cartridge is missing or not installed correctly.
To resolve the issue, correctly install the toner cartridge. If the toner cartridge is missing, skip to the step to install a new toner cartridge.

Step 1: Remove and reinstall the toner cartridge

Open the scanner assembly and top cover, remove the toner cartridge, reinstall it, and then try to print. For more detailed information, go to Replacing the Toner Cartridge.
If the error persists, continue to the next step.

Step 2: Install a new toner cartridge

Replace the toner cartridge with a new toner cartridge, and then try to print.
If the error persists, continue to the next step.

Step 3: Service the printer

If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document.

Er/08 displays, and the Supply and Ready lights are on

This condition occurs when the toner cartridge is very low and the Very Low Supply setting is set to Continue. You can continue printing until the print quality is no longer acceptable, or you can replace the toner cartridge.

Step 1: Replace the very low toner cartridge

Replace the toner cartridge with a new toner cartridge.
For more information about replacing the toner cartridge, go to Replacing the Toner Cartridge.
Try to print. If the issue persists, continue to the next step.

Step 2: Service the printer

If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document.

Er/08 displays, the Attention light blinks, the Supply and Ready lights are on, and the printer stops printing

An Er/08 error indicates that the toner cartridge is very low and the Very Low Supply setting is set to Stop. You can continue printing until the print quality is no longer acceptable, or you can replace the toner cartridge.

Step 1: Replace the very low toner cartridge

Replace the toner cartridge with a new toner cartridge.
For more information about replacing the toner cartridge, go to Replacing the Toner Cartridge.
Try to print. If the issue persists, continue to the next step.

Step 2: Service the printer

If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document.

Er/11 displays, the Attention and Supply lights blink, and the Ready light is on

This condition occurs when one of the following issues is detected:
  • The toner cartridge memory chip is missing
  • The toner cartridge packaging material is not removed

Step 1: Examine the toner cartridge

Open the toner cartridge access door, make sure the memory chip is not missing or damaged, and then make sure the toner cartridge packing material is removed.
  1. Open the toner cartridge door.
  2. Grasp the handle on the toner cartridge, and then pull the toner cartridge out to remove it.
  3. Make sure the toner cartridge packing material is removed.
  4. Examine the memory chip for damage.
    If the memory chip is missing or damaged, replace the toner cartridge.
  5. Align the toner cartridge with the tracks inside the printer, and then push the toner cartridge until it is firmly seated.
Try to print. If the issue persists, continue to the next step.

Step 2: Service the printer

If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document.

Er/14 or Er/17 displays, the Attention and Supply lights blink, and the Ready light is on

The toner cartridge has been protected on another printer or is an unauthorized toner cartridge.
Replace the affected supplies.

Step 1: Replace the incompatible toner cartridge

Replace the toner cartridge with a new toner cartridge and try to print. If the error persists, continue to the next step. For more detailed information, go to Replacing the Toner Cartridge.

Step 2: Service the printer

If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document.

Er/25 displays, the Attention light blinks, and the Ready light is on

An Er/25 error message indicates the loaded paper is not the correct size for the print job.
To resolve the error, load the correct size paper, or press the Start Copy button  to continue with the current size paper.

Er/30 to Er/66 displays and the Ready and Attention lights are on

An Er30, Er/50, Er/51, Er/52, Er/54, Er/55, Er/58, Er/59, or Er/66 error message indicates the printer is in an error state.

Step 1: Reset the printer

Resetting the printer can clear the error state.
  1. With the printer turned on, disconnect the power cord from the printer.
  2. Unplug the power cord from the power source.
  3. Wait 60 seconds.
  4. Reconnect the power cord to a wall outlet and to the printer.
    NOTE:
    HP recommends plugging the printer directly into a wall outlet.

Step 2: Plug the printer directly into an electrical outlet

Plug the product directly into an electrical outlet to make sure that the power source functions correctly.
  1. Disconnect the power cord from the rear of the product.
  2. Unplug the power cord from any power strips or surge suppressors.
  3. Plug the power cord directly into an electrical outlet.
  4. Reconnect the power cord to the rear of the product.
  5. Press the Power button () to turn on the product.
  6. Try the task again.
    If the issue persists, try a different electrical outlet.

Step 3: Service the printer

If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document.

Er/81 displays on the control panel, the Attention light blinks, and the Ready light is on

This condition indicates that the incorrect firmware is installed.
Install the correct firmware. For detailed information on downloading and installing the firmware, go to Updating or Upgrading Printer Firmware.

Go/01 displays, the Attention light blinks, and the Ready light is on

This condition indicates the printer is in a manual paper feed mode.
Load the correct paper type and size for the print job in the input tray, and then press the Start Copy button  to continue.

Go/02 displays, the Attention light blinks, and the Ready light is on

This condition indicates the printer is processing a manual duplexing print job and needs your assistance to finish the print job.
To finish the print job, remove the stack of printed pages from the output tray, and then load the stack with the printed side facing down and the top edge of the stack into the printer. Press the Start Copy button  to print the second sides.

https://support.hp.com/

Comments

Post a Comment

Popular posts from this blog

HP Laserjet Pro MFP M28W - 'User Intervention Required' Error (Windows)

Image
HP Laserjet Pro MFP M28W - 'User Intervention Required' Error (Windows) A  User Intervention Required  message displays on the computer, and the printer does not print. This issue might be caused by a printer error condition, corrupted print jobs, or wireless connection issues. Perform the following tasks in the order given. Use the printer after each task to see if the issue is resolved. Check for blinking lights or error messages When the printer does not respond or does not work as expected, look for an error message to find more helpful information. Check the printer control panel:  If lights on the printer are blinking or an error displays, follow any instructions on the printer control panel or printer software to resolve the error. If no instructions display, go to HP Customer Support, type your printer model, and then search for  blinking lights  or the specific error for detailed steps. Check the printer software or HP Smart app:  Errors and notificati
Read more

HP Laserjet Pro MFP M28W - 'Encryption Credentials Expired' error (macOS, iOS)

Image
HP Laserjet Pro MFP M28W - 'Encryption Credentials Expired' error (macOS, iOS) When printing from macOS or iOS, an  Encryption Credentials Expired  error message displays and you are unable to print. The error displays when the Embedded Web Server (EWS) has an expired certificate, and hence the operating system rejects the certificate. This Certification is necessary to secure connections with AirPrint and Secure Internet Printing Protocol (IPPs). To resolve the error, generate a new self-signed certificate from the EWS. Generate a new self-signed certificate from EWS Open EWS from a Windows computer, and then generate a new self-signed certificate. Use the desktop view of the EWS to generate the certificate. The mobile view of the EWS does not have the  Certificates  menu option. On a Windows computer, open an internet browser, and then enter the printer’s IP address. NOTE: For more information on how to open the EWS, see Use the HP Printer Embedded Web Serve
Read more